- Home
- Department of the Navy
- Notice
Moriah Wind System (MWS)
Department of Defense · Department of the Navy
Description
REQUEST FOR INFORMATION - SOURCES SOUGHT NAVAL AIR WARFARE CENTER, AIRCRAFT DIVISION LAKEHURST, NJ MORIAH WIND SYSTEM (MWS) THIS IS A REQUEST FOR INFORMATION ONLY. This Request for Information (RFI) is issued pursuant to FAR 15.201(e). This RFI is for information and planning purposes only and does not constitute a solicitation or promise to issue a solicitation in the future. It is a Market Research tool being used to identify potential technologies and eligible firms, of all sizes, prior to determining the method of acquisition and issuance of a solicitation. The Naval Air Warfare Center Aircraft Division (NAWC-AD) Lakehurst is seeking to continue the production of the U.S. Fleet wind systems for program management, production, systems engineering, logistics support and acceptance for the Moriah Wind System (MWS). The MWS program produces multiple configurations and variants of the MWS and associated components. A description of the Moriah Wind System follows: MWS provides digital wind speed and direction information, including crosswind and headwind, that supports decision making for air operations, combat, navigation, tactical planning and firefighting. The MWS replaces legacy Type F Wind Measuring and Indicating and Digital Wind Systems (DWS), providing a single wind measuring system, consistent across all ship classes, Land Based Test Site, and shore stations. MWS consists of the following main parts: Ultrasonic Wind Sensor Unit (WSU) with non-moving parts Wind Processor unit (WPU) consisting of dual redundant processors capable of interfacing with legacy wind and ship systems and Shipboard Local Area Networks (LANs) High-End Display (HED) with full range of available wind information and ship speed/ course data, including the display of Aircraft Recovery Bulletins (ARBs), Launch and Recovery Envelopes (LREs) and Final Course data. The HED is hardwired to one of the WSUs in a safety critical configuration to enable the display of wind data when the WPU or another connecting network is not functioning. HED fits inside an envelope no larger than11.50” high by 18.00” wide by 9.53” deep. This does not include maintenance access, connector access or environmental excursions. HED must be NVD compatible. Low-End Display (LED) with basic wind information and ship speed/course data. LED fits inside an envelope no larger than 7.36” high by 11.10” wide by 6.06” deep. This does not include maintenance access, connector access or environmental excursions. LED must be NVD compatible. The Air Temperature and Humidity Sensor (ATHU) is an accurate self-contained instrument for measuring external air temperature and humidity. The sensor electronics are enclosed in ruggedized stainless-steel housing. The Air Pressure Unit (APU) is an accurate self-contained instrument for measuring external air pressure. The sensor element and all associated electronics to produce a unidirectional serial data interface are housed in a cast aluminum box. The WSUs, HEDs and LEDs are uniform across ship classes, land-based test sites, and shore stations, with the quantity of each item dependent upon ship class/shore location. Every MWS has one WPU with dual-redundant processors, which will differ depending upon ship class and shore station either of which can individually perform all the functions necessary to keep MWS running. The sub-processors communicate with each other directly and periodically to determine functional status and to allow changes in control when a failure is detected. MWS accesses unclassified data only. There is a degree of system-to-system information exchange in MWS. Neither MWS nor its components are connected to the Global Information Grid (GIG). MWS data is output from its WPU in several ways: 1) synchro interfaces to provide wind information to legacy systems (SLQ-32, SPN-46, Integrated Launch and Recovery Television System (ILARTS), and Arresting Gear Crosscheck System); 2) serial and network interfaces for output of wind, navigational and system information to displays; and 3) network interfaces to communicate wind information to other ship systems and MWS displays. Currently, MWS will communicate over Aviation Data Management and Control System (ADMACS) on CVNs, through Digital Multiplex System (DMS) on DDGs and on a MWS controlled network on all other ship classes. Wind data is transmitted in the standard message format and protocol (SMF&P) data format and the National Marine Electronics Association (NMEA) data format. MWS receives the ARBs it displays through ADMACS via Network File System (NFS). MWS displays LREs that are programmed into the HEDs. In order to display ship’s speed and direction, calculate true wind speed and direction, as well as pitch and roll, MWS receives a data packet from Navigation Sensor System Interface (NAVSSI), which contains a host of navigational data, including ship’s positional information. MWS does not use any of this other information, although it must read the entire NAVSSI data packet prior to extracting the data required. The information in this packet is not sensitive unless the information is transmitted off the ship. However, MWS has no mechanism for transmitting data off the ship, nor any requirement to do so. MWS uses strictly defined data types for transmission into and out of the system. This information is limited to either NMEA ASCII strings using checksums to determine data integrity, structured binary data format using checksums to determine data integrity, proprietary DMS Light Internet Protocol (DLIP), and analog synchro resolver output to other ship systems. The data items themselves are confined to information from known systems (as defined in the relevant Interface Requirements Specifications) or is confined to IP addresses and ports specified in the Interface Design Documents (IDD) and the network architecture (ADMACS, DMS or other ship network). The components contain no TELNET or File Transfer Protocol (FTP) capability. Configuration
Truncated. Read the full description and attachments on SAM.gov.